Menu
Menu
Your Cart
Privacy Policy
We use cookies and other similar technologies to improve your browsing experience and the functionality of our site. Privacy Policy.

3D Printer Teensylu V0.8 Hi3D RepRap Prusa Mendel Control Board

3D Printer Teensylu V0.8 Hi3D RepRap Prusa Mendel Control Board
3D Printer Teensylu V0.8 Hi3D RepRap Prusa Mendel Control Board
3D Printer Teensylu V0.8 Hi3D RepRap Prusa Mendel Control Board
3D Printer Teensylu V0.8 Hi3D RepRap Prusa Mendel Control Board
3D Printer Teensylu V0.8 Hi3D RepRap Prusa Mendel Control Board
3D Printer Teensylu V0.8 Hi3D RepRap Prusa Mendel Control Board
3D Printer Teensylu V0.8 Hi3D RepRap Prusa Mendel Control Board
653 SEK
  • Stock: In Stock
  • SKU: SKU182576
3D Printer Teensylu V0.8 Hi3D RepRap Prusa Mendel Control Board

Description:


This is a project that is based on Sanguinololu. The ATmega644P has been replaced with an Atmel AT90USB1286 MCU. This Microcontroller has on-chip USB, removing the need for the FTDI USB UART. LUFA CDC bootloader preinstalled on the AT90USB1286 allows you to upload the firmware through USB cable directly. All of the through hole resistors and capacitors have been replaced with 0805 SMT components. Like the Sanguinololu the Teensylu has expansion headers supporting I2C, SPI, UART, and ADC pins. All extra I/O ports of the AT90USB have been broken out to headers for prototyping.

Features:

Size: 100 x 60mm    
Teensylu clone, Atmel's AT90USB1286
LUFA CDC bootloader preinstalled on the AT90USB1286 allows you to upload the firmware through USB cable.    
Up to 4 Pololu stepper driver boards on-board (X, Y, Z Extruder)

Supports multiple power configurations:

Logic & Motors supplied by ATX power supply (With ATX-4 12V 25A power)    
Motors supplied by 5mm screw terminal 7-35V
Logic supplied by USB 5V
With 2 thermistor connectors
With 2 N-MOSFETs for extruder/bed heaters    
With 1 low power MOSFET driver fan
Selectable 12v/5v endstop voltage    
With 4 endstops including, the 4th E-Stop to be used as an emergency stop

14 Extra pins available for expansion and development. 6 analog and 8 digital (Fully compatabile with Sanguinololu), with the following capabilities    
UART1 (RX and TX)    
I2C (SDA and SCL)    
SPI (MOSI, MISO, SCK)    
PWM pin (1)    
Analog I/O (6)

Package included:

1 x 3D Printer Teensylu V0.8 Hi3D RepRap Prusa Mendel Control Board








When you order from Bazaargadgets.com, you will receive a confirmation email. Once your order is shipped, you will be emailed the tracking information for your order's shipment. You can choose your preferred shipping method on the Order Information page during the checkout process. Bazaargadgets.com offers four different international shipping methods:

 

Shipping from Chinese Warehouse
Airmail and register airmailAreatime
United States,Canada10-20 business days
Australia,New Zealand,Singapore14-28 business days
United Kingdom, France, Spain, Germany, Netherlands, Japan, Belgium, Denmark, Finland, Ireland, Norway, Portugal, Sweden, Switzerland14-28 business days
Brazil15-35 business days
Russia15-35 business days
Other countries14-28 business days
Priority Direct MailAustria, Belgium,Denmark,Finland,France,Germany,Greece,Italy,Netherland,Portugal,Spain,Sweden7-10 business days
United States6-9 business days
United Kingdom5-10 business days
EMS10-15 business days to worldwide
Expedited Shipping5-8 business days to worldwide

 

NOTE: Netherlands Direct Mail has been combined into the Priority Direct Mail. If you are in a European country; simply choose Priority Direct Mail and it will be shipped via Netherlands Direct Mail.

 

*Expedited shipping can not be used for PO Box addresses

 

In addition, the transit time depends on where you're located. If you want to know more information, please contact the customer service. We will settle your problem as soon as possible. Enjoy shopping!

 

Write a review

Note: HTML is not translated!
Rating
Bad Good
Captcha